When I plugged in the projector wire to my Fujitsu laptop and pressed the projector function key, it will then black off for awhile and then show a sign 'out of rang' on the white screen that the projector screen on. The BenQ LU9245 BlueCore Laser Projector is the brightest choice for large venue applications, featuring superior 6500 ANSI-lumen brightness and 3,000,000:1 contrast ratio for brilliant viewing experiences even under bright ambient lighting. Streamlining features include Smart Projector Control with NFC *4 for mobile access to network configuration such as IP address setup. Not connecting from my laptop to projector using hdmi to hdmi cable, projector is showing signal out of range - 6559005 Thanks for your reply, to answer your question I am using a commercial purpose made VGA out cable that runs from the VGA outlet on the computers video card to the computers LCD monitor and the other outlet to the projector, I have seen similar setups work for others ie: in home entertainment setups etc but this particular one is not working eh!. Monitor Out. Also, if the resolution is set at a reasonable amount, make sure that the projector is plugged in all the way. Optoma makes a full range of projectors. The monitor can't "sync" with the video card, so it just displays an "Out of Range" error. Others are small enough to take on the road, but are really designed to stay … Unplug the connections from the laptop to the projector and turn off both. Anything else that I might have to manipulate on this Dell to get it to work VGA out to the projector? Je ne sais pas si c'est lié, mais mon écran devient noir d'un seul coup parfois (il ne se mais pas en veille, il est dans un autre état).
Several times throughout a meeting, we have to open up the remote and re-sync the projector to get the content back. Bringing massive brightness to tight installation spaces, the PT-RQ35K Series outputs 30,000 lm *2 from a body 60 % the size of our 26,000 lm *2 PT-RQ32K. Also, if the resolution is set at a reasonable amount, make sure that the projector is plugged in all the way. I always had this problem of not able to project my Fujitsu laptop screen on the projector during my presentation in class. Some are extremely portable, suitable for road warriors that travel and make presentations on the fly. Audio Settings. How to Connect an Optoma Projector to a Laptop. Monitor Out. Joined Jun 29, 2012 Messages 518. Category: Consumer Electronics. 2. 20_2_Many. Optoma projector range Spring 2017. ATTENTION OUT OF RANGE H:68.6KHz V:84.9Hz Its a Philips Monitor 105 G7. These projectors are not recommended for screens smaller than 120 inches in areas with high ambient light. 2. Selects various audio and video output settings A/V Output: select to output audio and video to an external device when the projector is in standby mode (Standby Mode must be turned on to use this setting) Monitor Out: Select the image source to output to an external device when the projector is in standby mode. When I plugged in the projector wire to my Fujitsu laptop and pressed the projector function key, it will then black off for awhile and then show a sign 'out of rang' on the white screen that the projector screen on. Selects various audio and video output settings A/V Output: select to output audio and video to an external device when the projector is in standby mode (Standby Mode must be turned on to use this setting) Monitor Out: Select the image source to output to an external device when the projector is in standby mode. Make sure there are no loose connections. The projector can't "sync" with the video card, so it just displays an "Out of Range" error. I get this massage when i connect my monitor. If the message is displaying on a secondary display simply go to Windows Display properties and change the resolution setting of the secondary display to a lower setting until and image is displayed. Submitted: 6 years ago. Also, if the resolution is set at a reasonable amount, make sure that the monitor is plugged in all the way. Hi! The projector can't "sync" with the video card, so it just displays an "Out of Range" error. I always had this problem of not able to project my Fujitsu laptop screen on the projector during my presentation in class. SERIAL/MULTI PROJECTOR SYNC IN: D-sub 9-pin (female) x 1 for external control (RS-232C compliant) SERIAL/MULTI PROJECTOR SYNC OUT : D-sub 9-pin (male) x 1 for link control (RS-232C compliant) REMOTE 1 IN: D-sub 9-pin (female) × 1 for external control (parallel) REMOTE 2 IN : M3 x 1 for wired remote control: REMOTE 2 OUT "OUT OF RANGE 96Khz 120Hz" s'affiche à l'écran mais le pc continue sa procédure de démarrage normalement.
... and can not seem to get the projector and laptop to sync up.